Land Rover Workshop Manuals - 300Tdi Discovery

AUTOMATIC GEARBOX

REPAIR

REPLACING TORQUE CONVERTER

1. Remove gearbox and transfer box assembly.

See LT230T Transfer Gearbox

2. Place gearbox on bench. Remove torque

converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.

3. Fit new torque converter using torque converter

handles 18G1501. Check dimension from
converter fixing boss to converter housing face is
50 mm. This shows converter is correctly seated
in housing.

4. Refit gearbox and transfer box assembly.

See

LT230T Transfer Gearbox

ELIMINATING LEAKS ON PUMP HOUSING

1. Remove gearbox and transfer box assembly.

See LT230T Transfer Gearbox

2. Place gearbox on bench. Remove torque

converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.

3. Remove twelve hexagonal bolts (inner ring

pattern).

4. Remove bell housing and pump assembly,

discard gasket.

5. Remove eight hexagonal bolts on rear of pump.

		[PREV PAGE] [NEXT PAGE]
Donate and help keep workshop manuals freely available. Other Land Rover Models Other Makes Discovery Workshop Manual - 2nd Edition - Eng Discovery Workshop Manual - 2nd Edition 01 - INTRODUCTION 04 - GENERAL SPECIFICATION DATA 05 - ENGINE TUNING DATA 07 - GENERAL FITTING REMINDERS 09 - LUBRICANTS, FLUIDS AND CAPACITIES 10 - MAINTENANCE 12 - ENGINE - Tdi 12 - ENGINE - V8i 12 - ENGINE - 4.0 V8 12 - ENGINE - Mpi 17 - EMISSION CONTROL 19 - FUEL SYSTEM - Tdi 19 - FUEL SYSTEM - MFI 19 - FUEL SYSTEM - SFI 19 - FUEL SYSTEM - Mpi 19 - FUEL SYSTEM - Cruise Control 26 - COOLING SYSTEM - Tdi 26 - COOLING SYSTEM - V8i 26 - COOLING SYSTEM - Mpi 30 - MANIFOLD AND EXHAUST SYSTEM 33 - CLUTCH 37 - MANUAL GEARBOX - R380 41 - TRANSFER GEARBOX 44 - AUTOMATIC GEARBOX - ZF DESCRIPTION AND OPERATION FAULT DIAGNOSIS ADJUSTMENT REPAIR LT230T TRANSFER GEARBOX WITH AUTOMATIC GEARBOX ASSEMBLY - V8 LT230T TRANSFER GEARBOX WITH AUTOMATIC GEARBOX ASSEMBLY - Tdi INHIBITOR SWITCH SELECTOR SHAFT OIL SEAL OIL SUMP OIL SCREEN CONTROL UNIT KICKDOWN CABLE EXTENSION HOUSING GOVERNOR ASSEMBLY GOVERNOR HUB PARKING PAWL MECHANISM REPLACING TORQUE CONVERTER ELIMINATING LEAKS ON PUMP HOUSING ELIMINATING LEAKS BETWEEN GEARBOX HOUSING AND INTERMEDIATE PLATE REPLACING PUMP GEAR SELECTOR-INTERLOCK SPECIFICATIONS, TORQUE SERVICE TOOLS 47 - PROPELLER SHAFTS 51 - REAR AXLE AND FINAL DRIVE 54 - FRONT AXLE AND FINAL DRIVE 57 - STEERING 60 - FRONT SUSPENSION 64 - REAR SUSPENSION 70 - BRAKES 74 - WHEELS AND TYRES 75 - SUPPLEMENTARY RESTRAINT SYSTEM 76 - CHASSIS AND BODY 80 - HEATING AND VENTILATION 82 - AIR CONDITIONING 84 - WIPERS AND WASHERS 86 - ELECTRICAL		Page 455 44 AUTOMATIC GEARBOX 18 REPAIR REPLACING TORQUE CONVERTER 1. Remove gearbox and transfer box assembly. See LT230T Transfer Gearbox 2. Place gearbox on bench. Remove torque converter using torque converter handles 18G1501, taking care not to damage torque converter/oil pump housing oil seal. 3. Fit new torque converter using torque converter handles 18G1501. Check dimension from converter fixing boss to converter housing face is 50 mm. This shows converter is correctly seated in housing. 4. Refit gearbox and transfer box assembly. See LT230T Transfer Gearbox ELIMINATING LEAKS ON PUMP HOUSING 1. Remove gearbox and transfer box assembly. See LT230T Transfer Gearbox 2. Place gearbox on bench. Remove torque converter using torque converter handles 18G1501, taking care not to damage torque converter/oil pump housing oil seal. 3. Remove twelve hexagonal bolts (inner ring pattern). 4. Remove bell housing and pump assembly, discard gasket. 5. Remove eight hexagonal bolts on rear of pump.
		[PREV PAGE] [NEXT PAGE]